AWS WAF

Open

In the AWS console, in the top menu, on the right side, select the desired region for log collection.

1. Open

   

2. In Amazon S3 URL, input the following link: https://s3-us-west-2.amazonaws.com/logs.armor.com/log-relay-aws-waf/log-relay-aws-waf.yaml.

   Open

   

3. Click Next.

4. In Stack name, enter a descriptive name.

   • This name must begin with a letter, and can only contain letters, numbers, and hyphens.

5. In ArmorLogEndpoint, enter the URL (including protocol and port number) of the endpoint to which logs will be sent.

   • This is the IP address or DNS name of the log relay instance, using the https protocol and port 5443.

6. In ArmorTenantId, enter your Armor account number.

   1. This can be found in the Account Overview section of your AMP account.

7. In BucketName, enter your S3 bucket name. This must be globally unique and bucket name should start with ‘aws-waf-logs’.

   • This is the S3 bucket (name) created by the CloudFormation template.

8. In BucketRetentionInDays, enter the number of days logs are retained in the S3 bucket.

   1. By default, Armor has configured 3 days; set to 0 to keep logs until manually removed.

9. In StrictSsl, indicate whether or not strict SSL checks should be enforced on the destination log URL (True or False).

11. In WebAclId, enter the ID of the AWS WAF Web ACL.

    Open

    

12. Click Next.

13. (Optional) If required by your organization, under Tags, add your organization's tags to the CloudFormation deployment.

14. (Optional) If required by your organization, under Permissions, in the drop-down menu, select IAM role ARN, and then in the corresponding field, enter AWSCloudFormationStackSetExecutionRole.

    Open

    

15. Review the information for the stack.

16. At the bottom of the screen, mark the box to accept the terms, and then click Create stack.

SSL/TLS Secured Communications

In most cases, we assume network isolation using subnetting and/or firewalls are in place to secure communication between a log source and your Log Relay. There are a few exceptions to this assumption:

In scenarios where it is typical to have data traverse the Internet, or in scenarios where a device only supports TLS-secured transport, the Log Relay config supports TLS ingestion.

Certificates

When you install the Log Relay software, a self-signed certificate and its corresponding private key are generated and placed in /opt/armor/logrelay.pem and /opt/armor/logrelay.key respectively. If the device sending logs requires strict SSL checks, you have a few options to satisfy this requirement:

Exporting the Self-Signed Certificate

You may export the certificate and add it to the trust store of the log source device (if supported). You copy the PEM certificate from the Log Relay server and then consult the vendor-supplied documentation to install a new trusted certificate.

Using a Certificate from a Valid CA

You can also generate a CSR and request a certificate from a CA the log source device already trusts. Using openssl you can generate a new CSR. We recommend using a configuration file to supply Subject Alternate Names (SANs) for the various DNS hostnames pointed at your Log Relay in addition to its IP address.

logrealy.cnf

Fill in the values in angle brackets above with applicable values. For <COUNTRY> us the 2-digit ISO country code. For <STATE>. you can use the 2-digit abbreviation or the full name of your state or province.

If the IP address of the Log Relay changes frequently or you already use a DNS hostname as the default means of addressing the Log Relay, use the DNS hostname instead of the IP address in <LOG_RELAY_IP_ADDRESS>.

Add any DNS hostnames that resolve to this Log Relay using the alt_names section of the config. If you're not using any SANs, remove the [alt_names] and [req_ext] sections and remove the
reference under the [req] section.

Then use openssl to request the certificate:

Note that you may need to run this command as root as the key is owned by the Log Relay service account.

After you've generated your CSR and received the certificate from the CA, ensure that it is in PEM format and upload it to your Log Relay machine. Ensure that is accessible to the Log Relay service account.

Once the file is uploaded and has the correct permissions, update the override environment file to point at the path of the new certificate. Create a file at /etc/sysconfig/armor-logstash.override with the following contents:

If you used a key other than the one included with the Log Relay, you can specify it in this file as well:

Note that this key must not have a password and be in PKCS8 format. You can use file permissions and/or selinux policies to protect the key.

After creating or updating these configuration files, restart the Log Relay service: